Outdoor, Landscape & Security Lighting
Landscape, security & exterior lighting installed for Pascack Valley homes — pathways, facades, motion & dusk-to-dawn. Pascale Electric — (201) 391-7759.
Pascale Electric, Inc. — 130 Kinderkamack Road, Park Ridge, NJ 07656.
Call (201) 391-7759
or email info@pascaleelectric.com.
The short answer
Exterior lighting splits into two systems: line-voltage 120-volt fixtures for facade, soffit, and security lighting, and low-voltage landscape lighting fed by a transformer for path, garden, and uplighting. Line-voltage exterior receptacles and most outdoor circuits require ground-fault protection, weather-resistant devices, and in-use covers, and direct-buried cable has minimum burial depths set by the code. Most residential projects take one to three days depending on trenching, and new exterior circuits require a permit in New Jersey.
Outdoor, Landscape & Security Lighting — key facts
- Typical timeline
- One day for facade and security fixtures; two to three when trenching a landscape system.
- Permit required
- Yes for new exterior circuits and receptacles; not for replacing an existing fixture with a like item.
- Power interruption
- Only the circuit being worked on, briefly.
- Two systems
- Line-voltage 120V for facade, soffit, and security; low-voltage through a transformer for landscape.
- Burial depth
- Set by code and varies by wiring method — direct-buried cable goes deeper than cable in conduit.
You need this if
- The front walk, side path, or back steps are dark and someone has already tripped on them.
- You have one builder-grade fixture by the door and the rest of the house disappears after sunset.
- Landscaping you paid real money for is invisible for half the year and most of every day.
- You want motion or dusk-to-dawn lighting at the garage, side yard, and back of the house for security.
- A pool, patio, or outdoor kitchen gets used at night and there is no lighting plan for it.
- Existing exterior fixtures are corroded, filled with water, or on a switch nobody can find.
Outdoor, Landscape & Security Lighting
Good exterior lighting makes a home safer, more secure, and more beautiful. We install pathway and landscape lighting, facade and accent lighting, and motion or dusk-to-dawn security fixtures on weather-rated circuits.
What we install
Path and garden lighting, uplighting and facade accents, soffit and porch fixtures, and motion-activated or dusk-to-dawn security lights — all on properly rated outdoor circuits with GFCI protection.
How the job runs
- Walk the property after dark
- Daytime planning misses the point of exterior lighting. Walking the property at night shows where the actual hazards are, where a neighbor's light already covers you, where glare would spill into a bedroom window, and which features are worth lighting versus which just look good on a plan.
- Decide line-voltage, low-voltage, or both
- Most properties end up with both: line-voltage for soffit, facade, and security fixtures that need output and permanence, and a low-voltage system for path and garden lighting where fixtures move as the landscape matures. That decision determines the circuit design, the trenching, and the controls.
- Design the circuit and the control scheme
- We plan the circuit, the transformer size and location for a low-voltage system, and how you want it to turn on — photocell, astronomic timer, motion, smart control, or a combination. Controls are what make an outdoor system get used rather than left off.
- Trench and run
- Trenching follows the beds and lawn edges wherever possible to minimize disruption, at the burial depth the code requires for the wiring method being used. Conduit is used under driveways, walks, and anywhere a future shovel is likely.
- Set fixtures and terminate
- Fixtures are set, leveled, and aimed, connections are made in listed weatherproof enclosures, and every exterior receptacle gets a weather-resistant device and an in-use cover. Wet-location fixtures go where they are exposed; damp-location fixtures under cover.
- Aim at night and set the controls
- Final aiming happens after dark, because that is the only time you can see glare, hot spots, and where a beam is missing its target. Timers and photocells are set, and if the system is on a smart control, the schedule is configured before we leave.
What's included
- Nighttime walkthrough and lighting plan for the property
- Line-voltage circuits with ground-fault protection where required
- Transformer sizing, mounting, and connection for a low-voltage system
- Trenching along planned routes at code burial depth, with conduit under hard surfaces
- Weather- or wet-location-listed fixtures set, leveled, and aimed
- Weather-resistant receptacles with in-use covers at exterior outlets
- Photocell, timer, motion, or smart control installation and configuration
- Final aiming after dark and permit filing where new circuits are added
What's not included
- Landscape restoration beyond backfilling and reasonably reseeding a trench line
- Removing, relocating, or replanting shrubs and trees in the trench path
- Cutting and patching driveways, walkways, patios, or other hardscape
- Irrigation system repair if a line is encountered during trenching
- Fixtures you supply that are not listed for the location they are going in
- Seasonal or holiday lighting installation and removal
- Repositioning fixtures in future seasons as plantings grow in
- Security camera systems, network cabling, and low-voltage data
What affects the cost
- Trenching distance and what the trench crosses
- The largest variable on a landscape system. Open lawn is fast; a run that crosses a driveway, a paver walk, mature root systems, or a septic field is a different job.
- Line-voltage vs. low-voltage
- Low-voltage fixtures are cheaper per point and shallower to bury, but require a transformer and careful load balancing. Line-voltage costs more per fixture but delivers more output and covers longer distances without voltage drop.
- Fixture count and quality
- The gap between a big-box aluminum fixture and a cast-brass or copper one is significant — and in this climate, with road salt, freeze-thaw, and humid summers, the cheap ones are replaced within a few seasons.
- Where the power comes from
- Tapping an existing exterior circuit with capacity is straightforward. Running a new home run from the panel, especially out of a finished basement and through a foundation wall, adds meaningful work.
- Controls
- A photocell is the simplest option. Astronomic timers, zone control, motion integration, and smart-controlled systems each add cost, and multiple independently switched zones multiply it.
- Mounting conditions
- Soffit and wood siding are straightforward. Stone, brick, stucco, and hardscape mounting require different anchoring, careful sealing, and more time.
- Restoration expectations
- Backfilling a lawn trench is one thing; restoring a manicured planting bed or a specimen lawn to its prior state is a landscaping scope worth budgeting for separately.
Line-voltage exterior lighting vs. low-voltage landscape lighting
- Best for — Line-voltage (120V): Soffit, facade, security, floodlights, long runs — Low-voltage (transformer-fed): Path, garden, uplighting, accent, water features
- Output — Line-voltage (120V): Highest available — Low-voltage (transformer-fed): Ample for accent and path work
- Burial depth — Line-voltage (120V): Deeper, per code for the wiring method — Low-voltage (transformer-fed): Shallowest of the options
- Moving a fixture later — Line-voltage (120V): Difficult — it is a wired circuit — Low-voltage (transformer-fed): Easy — that is the main appeal
- Distance limits — Line-voltage (120V): Long runs without meaningful voltage drop — Low-voltage (transformer-fed): Voltage drop limits run length; needs balanced loading
- Safety around planting beds — Line-voltage (120V): Requires proper burial and GFCI protection — Low-voltage (transformer-fed): Very low shock risk if a cable is nicked
- Cost per fixture — Line-voltage (120V): Higher — Low-voltage (transformer-fed): Lower
- Typical result — Line-voltage (120V): Security and architectural lighting — Low-voltage (transformer-fed): The layered garden look most homeowners want
Permits and code
- Outdoor receptacles at dwellings require ground-fault protection, weather-resistant devices, and an enclosure that keeps water out while a cord is plugged in — an in-use cover, not a flip lid, at any location where something stays connected.
- Minimum burial depths are set by the code and depend on the wiring method and circuit. Direct-buried cable goes deepest; cable in rigid or intermediate metal conduit can be shallower; and residential branch circuits rated 120 volts or less, GFCI-protected and limited in overcurrent rating, are permitted at a reduced depth. Low-voltage landscape systems have their own reduced requirement.
- Fixtures must be listed for the environment they are in. A damp-location listing covers protected areas like a soffit or a covered porch; anything exposed to direct rain and snow requires a wet-location listing. This is one of the most common reasons an exterior fixture fails early.
- Underground conduit and raceways entering a building must be sealed against moisture migration, and boxes and enclosures used outdoors must be listed for wet locations with drainage where the code requires it.
- Adding a new exterior circuit or receptacle requires a permit and inspection under the New Jersey Uniform Construction Code. Replacing an existing exterior fixture with a like item is ordinary maintenance and does not.
- Lighting near pools, spas, and water features falls under separate and much stricter requirements for clearance, bonding, and GFCI protection than ordinary landscape lighting — the rules change entirely once a fixture is within the defined distance of the water.
In Bergen County & the Pascack Valley
Exterior lighting in the Pascack Valley has to survive a specific set of local conditions. Winter road salt and repeated freeze-thaw cycles destroy inexpensive aluminum path fixtures within a few seasons, which is why cast brass and copper are worth the difference on anything near a driveway or walk. Mature tree canopy — heavy through River Vale, Washington Township, Wyckoff, Franklin Lakes, Saddle River, and Upper Saddle River — cuts both ways: it makes uplighting genuinely dramatic, and it means roots to work around when trenching and falling limbs that take fixtures out during storms. The deep, wooded lots in Saddle River, Upper Saddle River, and Franklin Lakes push runs long enough that voltage drop becomes a real design constraint on a low-voltage system rather than a footnote, while the tighter lots in Emerson, Westwood, and Park Ridge make glare into a neighbor's window the constraint that actually matters. Several boroughs here also have dark-sky and nuisance-lighting language in their ordinances, so aiming and shielding are not purely aesthetic decisions. And the same Pascack Brook and Hackensack River drainage that floods basements affects where a transformer and exterior receptacles can sensibly be mounted.
Outdoor, Landscape & Security Lighting FAQs
- Can you add outdoor outlets or lighting controls?
- Yes — we add weather-rated outlets, timers, photocells, and smart controls so your exterior lighting runs automatically.
- Will landscape lighting survive being hit by a lawn mower or a snow blower?
- Better fixtures will, and placement matters as much as the fixture. Cast brass and copper path lights tolerate an accidental clip and can be straightened; thin aluminum and plastic ones do not. The bigger factor is setting fixtures back into beds rather than at the lawn edge, and keeping cable runs off the mowing line. If a fixture does get hit, a low-voltage system is easy to repair — that is one of its real advantages over a buried line-voltage circuit.
- How should the lights turn on and off?
- The control decides whether the system gets used. A photocell is the simplest and turns on at dusk, but it stays on until dawn unless paired with a timer. An astronomic timer tracks sunset through the year and can shut zones off at a set hour, which is usually the best default. Motion sensing suits security fixtures at the garage and side yard but is wrong for accent lighting. Many homeowners end up combining them: accent lighting on an astronomic timer, security on motion.
- Can I add landscape lighting later without redoing the trenching?
- This is exactly where low-voltage systems earn their keep. If the transformer is sized with headroom and the cable runs are planned with future taps in mind, adding fixtures later is straightforward — the connection points are accessible and no new trench is required for fixtures near an existing run. It is worth mentioning your future plans at design time, because oversizing the transformer and running slightly heavier cable up front costs very little and saves a second trenching job.
- How bright should exterior lighting be?
- Dimmer than most people expect. The eye adapts to darkness, so modest output reads as well-lit at night, and overly bright fixtures create glare that actually makes it harder to see — a too-bright floodlight puts everything beyond it into deeper shadow. Good exterior lighting uses lower output, more fixtures, and careful shielding so you see the illuminated surfaces rather than the light source. This also keeps you on the right side of neighbors and municipal nuisance-lighting language.
- Are solar path lights a reasonable alternative?
- For a temporary marker on a walkway, they are fine. As a lighting system, they are not comparable — output is low and inconsistent, batteries degrade within a couple of seasons, and performance collapses under the tree canopy that covers most properties here, in exactly the months when it is dark at five in the afternoon. If the goal is genuinely seeing where you are walking and having the house look intentional after dark, a wired low-voltage system is a different category of result.
- What is the difference between damp-rated and wet-rated fixtures?
- It is about direct exposure to water, and it is not a marketing distinction. A damp-location listing is for places protected from direct rain — a covered porch ceiling, a deep soffit, a sheltered entryway. A wet-location listing is required for anything exposed to rain, snow, and sprinkler spray, which is most exterior fixtures. Installing a damp-rated fixture in a wet location is a code violation, and practically it means water gets into the housing, corrodes the socket, and kills the fixture in a season or two.
Towns we serve
- Electrician in Park Ridge, NJ
- Electrician in Woodcliff Lake, NJ
- Electrician in Montvale, NJ
- Electrician in Hillsdale, NJ
- Electrician in River Vale, NJ
- Electrician in Westwood, NJ
- Electrician in Washington Township, NJ
- Electrician in Emerson, NJ
- Electrician in Oradell, NJ
- Electrician in Upper Saddle River, NJ
- Electrician in Saddle River, NJ
- Electrician in Franklin Lakes, NJ
- Electrician in Wyckoff, NJ
- Electrician in Allendale, NJ
- Electrician in Ramsey, NJ